Home › Blog › Advice & Guidance
Does the door or frame need measuring?
Ahead of fitting most replacement doors, in case of any shrinking or swelling to the present door, you should measure the actual frame so that you get the true opening and correct sizing. If there isn’t a frame, go brick-to-brick with your tape measure and subtract the frame size from the relevant measurement.
-
What door gaps should be left?
There needs to be several small and even gaps around the door edges so that no catching occurs when opening and closing a new door. No scuffing should take place with gaps of about 3mm at the top and sides and 9mm at the bottom. An element of lipping exists in most new types of doors to allow a fitter to plane or trim a door and get the necessary clearance.
-
What are the standard sizes of UK internal doors?
Recognise that manufacturers tend to follow a series of common door sizes if wanting to discover how to measure a door. 1981 x 762 x 35 mm (approximately 6’6” × 2’6”) is the conventional door size, but not always. Here are some other UK internal door sizes you may come across:
– 1981 × 610 × 35 mm (6’6” × 2’0”)
– 1981 × 686 × 35 mm (6’6” × 2’3”)
– 1981 × 838 × 35 mm (6’6” × 2’9”)
– 2040 × 826 × 40 mm (metric size)
Thickness can vary as well, such as with fire-rated doors (FD30), which surpass a standard internal door’s thickness by roughly 9 mm (44 mm as opposed to 35 mm).
Refrain from ordering until you have captured the size closest to the standard and know the trimming options
-
With no frame, how do you measure?
If there’s no frame to work with, measuring doors needs you to directly measure the brickwork opening. The width can be gathered by going brick to brick in a straight line across the top, middle and bottom of the opening and noting the smallest measurements. To get the height, go brick to brick in a straight line once again, but from the left, centre and right sides of the opening, logging the small measurements. These dimensions will enable you to work out the necessary door set size, assuming you’ve deducted the specified allowance. An undersized opening will cause a range of problems, so it’s safer to go oversized as at least then an installer can pack an undersized frame, if needed.
Measuring openings with frames (internal or external door replacements)
On measuring for a doorset in the instance of upgrading an internal or external door, standard practice is to do so with the door frame in place.
You can swear by our knowledge of how to measure a door frame when we tell you to take measurements from inside for a comfortable fit into any existing frame structure.
Our numbered steps will see that you don’t put a foot wrong with this bit:
- Measuring the distance between the inside edges of the frame at the top, middle and bottom will give you the width.
- Ascertain the door height with a measurement at different points from the top frame to the floor (or threshold, if there is one) – the smallest measurement is the one to use.
- You mustn’t neglect to measure the depth of the door frame and door rebate (where the door sits in the frame) to be assured of precise alignment.
- So that it hangs right, be alert to the door opening inwardly or outwardly and being left- or right-handed.
- Last thing. Ensure the frame is exactly square, which a diagonal measurement from corner to corner will tell you.
Clearances, trimming and floor coverings
No piece on how to measure a door is worth its salt if it doesn’t say to make considerations for clearances around edges.
With a clearance of around 3mm at the top and side and 9mm at the bottom, door operation should be simple enough and leaves space in case of any future contraction or expansion.
Read the manufacturer guidelines to become au fait with the trimming limits so that your new door works and fits as hoped.
Our numbered steps will see that you don’t put a foot wrong with this bit:
- Measuring the distance between the inside edges of the frame at the top, middle and bottom will give you the width.
- Ascertain the door height with a measurement at different points from the top frame to the floor (or threshold, if there is one) – the smallest measurement is the one to use.
- You mustn’t neglect to measure the depth of the door frame and door rebate (where the door sits in the frame) to be assured of precise alignment.
- So that it hangs right, be alert to the door opening inwardly or outwardly and being left- or right-handed.
- Last thing. Ensure the frame is exactly square, which a diagonal measurement from corner to corner will tell you.
Mapping measurements to UK sizes (and when to choose the bespoke option)
our measurements will hopefully match up to common standard internal door sizes in the UK, including widths of 540mm to 838mm, heights of 1981mm or 2040mm and thicknesses of 35 to 44mm.
Gauge if a standard door will neatly integrate by calculating expected gaps; 2-3mm at the top, 2mm each side and 8-10mm at the bottom for clearance. If trimming can accomplish these clearances, a standard door will be fine.
Something tailored is advised if an opening is greatly bigger than standard dimensions, irregular or has a non-standard thickness.
Eden Windows is well-accustomed to measuring a door if you’d rather leave it to the professionals and we wouldn’t expect you to do it anyway after placing a door order with us. It’s our job and we’ll do it with our usual efficiency so that your replacement door looks and works a treat.